If you’re a proud owner of a 2006 Honda CR-V, you may have encountered the need to reset your dashboard after an oil change. Whether you’re an experienced DIY mechanic or just starting out, understanding the steps involved in this process can help you maintain your vehicle’s optimal performance. In this comprehensive guide, we will walk you through the simple procedure of resetting your 2006 Honda CR-V dashboard after an oil change, equipping you with the necessary knowledge to keep your vehicle running smoothly for years to come.
Before embarking on this task, it’s crucial to gather the necessary tools and materials. You will need a basic set of wrenches, a funnel, and fresh engine oil that meets your vehicle’s specifications. Additionally, a pair of safety glasses and gloves are recommended to ensure your protection while working on your vehicle. Once you have assembled the required items, you can begin the oil change process by locating the oil drain plug beneath your engine. Carefully remove the plug and allow the old oil to drain into an oil pan. While the oil is draining, replace the oil filter with a new one, ensuring it is properly tightened. Once the oil has drained completely, replace the drain plug and add the fresh oil through the oil filler cap.
After completing the oil change, it’s time to reset your dashboard. This process varies slightly depending on the trim level of your 2006 Honda CR-V. For models equipped with a maintenance minder system, you can reset the system by following the steps outlined in your vehicle’s owner’s manual. Alternatively, if your CR-V does not have a maintenance minder system, you can manually reset the dashboard by turning the ignition key to the “ON” position without starting the engine. Locate the trip reset button on your dashboard and press and hold it until the display reads “000000.” Once the display resets, start your engine and verify that the oil life indicator has been reset.
Resetting the Oil Life Indicator
When your 2006 Honda CR-V’s oil life indicator is due for a reset, you can easily do it yourself with a few simple steps:
- Locate the oil life indicator display on your dashboard. It’s usually located near the speedometer and tachometer.
- Turn the ignition key to the “ON” position, but do not start the engine.
- Press and hold the “Trip” button on the dashboard until a message appears that says “Oil Life Reset.”
- Release the “Trip” button.
- Restart the engine to ensure the oil life indicator has been reset.
Here’s a more detailed explanation of each step:
Step 1: Locate the oil life indicator display on your dashboard.
The oil life indicator display is usually located in the center of the dashboard, near the speedometer and tachometer. It’s a digital display that shows the percentage of remaining oil life.
Step 2: Turn the ignition key to the “ON” position, but do not start the engine.
Turn the ignition key to the “ON” position, but do not start the engine. The oil life indicator display should come on.
Step 3: Press and hold the “Trip” button on the dashboard until a message appears that says “Oil Life Reset.”
Locate the “Trip” button on the dashboard. It’s usually located on the left side of the steering wheel, near the instrument panel. Press and hold the “Trip” button until a message appears that says “Oil Life Reset.”
Step 4: Release the “Trip” button.
Once the “Oil Life Reset” message appears, release the “Trip” button.
Step 5: Restart the engine to ensure the oil life indicator has been reset.
Restart the engine to ensure the oil life indicator has been reset. The oil life indicator display should now show 100%.
Locating the Reset Button
The oil life indicator reset button in a 2006 Honda CR-V is located on the instrument cluster, to the right of the odometer. It is a small, black button with the word “RESET” printed on it. To reset the oil life indicator, follow these steps:
1. Turn the ignition key to the “ON” position. Do not start the engine.
2. Press and hold the “RESET” button for about 10 seconds. The oil life indicator will begin to flash.
3. Continue holding the “RESET” button until the oil life indicator stops flashing and resets to 100%.
4. Release the “RESET” button. The oil life indicator has now been reset.
Preparing the Vehicle
Before resetting the dash after an oil change in your 2006 Honda CR-V, it’s crucial to follow these steps to ensure proper vehicle preparation:
1. Safety First
Park your vehicle on a flat surface and engage the parking brake to prevent any movement. Ensure that the ignition switch is in the “Off” position.
2. Gather Tools and Materials
You’ll need the following items:
- Replacement engine oil filter
- New engine oil (refer to your owner’s manual for specifications)
- Oil pan
- Oil filter wrench
- Funnel
3. Accessing the Engine Oil
Locate the engine oil dipstick and pull it out. Wipe it clean with a rag and reinsert it fully. Withdraw it again and check the oil level. If the oil level is below the “Low” mark, you’ll need to add oil before continuing with the oil change. Use a funnel to pour the new oil into the engine until the level reaches the appropriate mark on the dipstick.
| Procedure | Description |
|---|---|
| Step 1 | Place an oil pan under the oil drain plug located on the bottom of the oil pan. |
| Step 2 | Using an oil filter wrench, carefully loosen the oil drain plug and allow the oil to drain into the pan. |
| Step 3 | Locate the old oil filter and remove it by turning it counterclockwise. |
| Step 4 | Lubricate the gasket of the new oil filter with clean oil and screw it into place hand-tight. |
| Step 5 | Tighten the oil drain plug back into the oil pan. |
| Step 6 | Reinsert the oil dipstick and check the oil level. Add more oil if necessary. |
Initiating the Reset Procedure
To initiate the reset procedure, begin by turning the ignition to the “ON” position without starting the engine. Ensure that the odometer is displayed on the instrument cluster. Next, locate the “Select/Reset” button on the instrument panel, typically located on the right-hand side. Press and hold the button for approximately 5 seconds until the “ODO” indicator on the instrument cluster starts blinking. This action triggers the reset process.
Setting the Maintenance Interval
After holding the button for 5 seconds, the blinking “ODO” indicator will prompt you to set the maintenance interval. Use the “Select/Reset” button to scroll through the available options, typically ranging from 5,000 to 10,000 miles or 3 months to 12 months. Select the desired maintenance interval by pressing the button to confirm your choice. The “ODO” indicator will stop blinking, confirming the new interval.
Completing the Reset Process
To complete the reset process, turn the ignition to the “OFF” position and wait a few seconds. Then, restart the engine, and the maintenance reminder light should be reset. Verify that the new maintenance interval is displayed correctly on the instrument cluster. If any issues arise during the process, refer to your vehicle’s owner’s manual for specific instructions or consult a qualified mechanic.
Maintenance Settings Table
| Interval | Value |
|---|---|
| 5,000 Miles | 5000mi |
| 10,000 Miles | 10000mi |
| 3 Months | 03MO |
| 6 Months | 06MO |
| 12 Months | 12MO |
Completing the Oil Change
Once you have drained all of the old oil, it is important to replace the oil drain plug and tighten it securely. Next, locate the oil filter and remove it using an oil filter wrench. Apply a thin layer of new oil to the gasket of the new oil filter and screw it on by hand until it is snug. Do not overtighten the oil filter.
Now, add new oil to the engine. The amount of oil you need will vary depending on your vehicle, so consult your owner’s manual for the specific recommended amount. Once you have added the correct amount of oil, replace the oil cap and start the engine. Let the engine run for a few minutes to circulate the new oil.
Resetting the Oil Life Indicator
Once you have completed the oil change, it is important to reset the oil life indicator so that it accurately reflects the remaining life of the new oil. To do this, follow these steps:
1. Turn the ignition key to the “ON” position, but do not start the engine.
2. Press and hold the trip odometer reset button for 5-10 seconds. A wrench icon will appear on the display.
3. Continue holding the button until the wrench icon disappears and the oil life percentage resets to 100%.
4. Release the button and start the engine. The oil life indicator should now be reset.
5. If the oil life indicator does not automatically reset, you may need to manually reset it using a scan tool. Consult your owner’s manual for specific instructions on how to do this.
Table: Oil Capacities for 2006 Honda CR-V
| Engine | Oil Capacity (quarts) |
|---|---|
| 2.4L | 4.5 |
| 2.0L | 4.1 |
Verifying the Reset
To confirm that the oil change reset was successful, follow these steps:
- Turn off the engine and wait for a few seconds.
- Turn the ignition key to the “ON” position, but do not start the engine.
- Press and hold the “Trip” button on the instrument cluster for at least 5 seconds.
- Release the button when the display shows “Maintenance Required” or a similar message.
- Press the “Trip” button again to reset the interval to the desired mileage or time.
- Turn off the ignition and restart the engine to verify that the reset was successful. The “Maintenance Required” message should no longer appear.
Additional Verification Steps:
In some cases, it may be necessary to perform additional steps to ensure that the reset is complete:
- Disconnect the negative terminal of the battery for 10 seconds and then reconnect it.
- Use an OBD2 scanner to clear any stored diagnostic trouble codes (DTCs) related to the oil change interval.
- Take the vehicle for a short drive to allow the computer to relearn the oil change information.
Troubleshooting Common Issues
1. The Reset Button Doesn’t Work
Try pressing the reset button several times. If it still doesn’t work, check the fuse box for a blown fuse. If there is a blown fuse, replace it with a new one of the same amperage.
2. The Oil Life Indicator Doesn’t Reset
Make sure you pressed the reset button for the full seven seconds. Also, check to make sure that the new oil filter is properly installed and tightened.
3. The Oil Life Indicator Resets Itself
If the oil life indicator resets itself after you reset it, there may be a problem with the instrument cluster. You will need to take your vehicle to a mechanic to have it diagnosed.
4. The Oil Life Indicator Is Not Accurate
The oil life indicator is only an estimate. It may not be accurate if you drive in severe conditions, such as stop-and-go traffic or extreme temperatures.
5. The Oil Life Indicator Is Not Displaying
The oil life indicator may not be displaying on your instrument cluster if the battery has been disconnected or replaced.
6. The Oil Life Indicator Is Flashing
The oil life indicator may be flashing to indicate that it is time for an oil change. You should have your oil changed as soon as possible.
7. The Oil Life Indicator Is Not Resetting After an Oil Change
If you have followed all of the steps above and the oil life indicator is still not resetting, you may need to have your vehicle’s computer reset by a mechanic. This will clear all of the stored data and allow you to reset the oil life indicator.
| Step 1: | Locate the reset button on your instrument cluster. |
| Step 2: | Press and hold the reset button for seven seconds. |
| Step 3: | The oil life indicator should now be reset. |
Resetting the Oil Change Reminder Light
1. Locate the “Maintenance Required” Button
It’s typically situated on the lower left corner of the dashboard.
2. Turn the Ignition On
Don’t start the engine; just ensure the instrument panel lights are illuminated.
3. Hold the Button for 5-10 Seconds
Keep it depressed until the reminder light flashes and then stays lit.
4. Turn the Ignition Off
Remove the key to completely power off the vehicle.
5. Wait 10 Seconds
Give the system time to fully reset.
6. Turn the Ignition On Again
Start the engine to confirm the light has been reset.
7. Release the Button
The “Maintenance Required” light should now be off.
8. Advanced Troubleshooting
If the light doesn’t reset after following these steps, try the following:
Check for any error codes: Use an OBD2 scanner to retrieve any active codes. If there are any related to the oil change reminder, address them.
Disconnect and reconnect the battery: This can sometimes reset the system. After disconnecting the battery, wait a few minutes before reconnecting it.
Check the electrical connections: Ensure all connections to the oil change reminder system are secure and free of corrosion.
Using a Scan Tool for Resetting
A scan tool is a specialized device used to diagnose and reset various automotive systems, including the oil life monitoring system. Here’s a detailed guide on how to reset the oil change indicator using a scan tool:
Step 1: Gather Materials
You’ll need a compatible scan tool and a vehicle-specific connector cable. Ensure the scan tool supports resetting the oil life monitor function for your 2006 Honda CR-V.
Step 2: Connect the Scan Tool
Plug the scanner’s cable into the vehicle’s diagnostic port, typically located under the dashboard or in the engine compartment.
Step 3: Power On the Scan Tool
Turn on the scan tool and follow the on-screen instructions to navigate to the service menu or maintenance reset section.
Step 4: Select Vehicle Information
Enter the vehicle’s make, model, and year using the scan tool’s controls. This ensures the scan tool has the correct settings for your CR-V.
Step 5: Locate Oil Life Reset Function
Navigate through the scan tool’s options to find the function responsible for resetting the oil life monitor. It may be labeled “Oil Reset,” “Maintenance Reset,” or similar.
Step 6: Select Yes to Reset
Once you find the oil reset function, select “Yes” or “OK” to confirm the reset. The scan tool will initiate the process and display a confirmation message.
Step 7: Check Oil Life Meter
Turn off the scan tool and restart the vehicle. The oil life monitor should now display the correct mileage or percentage based on the factory specifications.
Troubleshooting Tips
– Ensure the scan tool is compatible with the 2006 Honda CR-V.
– Check the scan tool’s instructions for specific reset steps.
– If the reset is unsuccessful, verify the vehicle’s diagnostic port is functioning correctly.
Maintaining Proper Oil Intervals
Regular oil changes are crucial for maintaining optimal engine performance and longevity. The following table provides recommended oil change intervals for the 2006 Honda CR-V:
| Drive Condition | Oil Change Interval |
|---|---|
| Normal driving | 5,000 miles or 6 months |
| Severe driving (e.g., towing, off-roading) | 3,000 miles or 3 months |
It’s important to note that these intervals are general guidelines and may vary depending on specific driving habits and conditions. You should consult your vehicle’s owner’s manual for specific recommendations and adjust the oil change schedule as needed.
Regular oil changes are essential for:
– Removing contaminants and impurities
– Lubricating engine components
– Reducing friction and wear
– Preventing sludge and deposit formation
– Maintaining optimal oil viscosity
Neglecting oil changes can lead to premature engine wear, decreased performance, and costly repairs. By following the recommended oil change intervals, you can help ensure the longevity and reliability of your 2006 Honda CR-V.
How To Reset Dash After Oil Change 2006 Honda CR-V
Tools You’ll Need:
- 10mm socket wrench
- Oil filter wrench
- New oil filter
- 5 quarts of new oil
Instructions:
- Locate the oil filter. It is usually located on the front of the engine, near the bottom.
- Place the oil filter wrench on the oil filter and loosen it. Do not remove it completely.
- Allow the oil to drain into the oil pan.
- Remove the old oil filter and install the new one. Tighten the oil filter using the oil filter wrench.
- Add 5 quarts of new oil to the engine.
- Check the oil level using the dipstick. The oil level should be between the “min” and “max” marks.
- Start the engine and let it run for a few minutes. This will circulate the new oil throughout the engine.
- Turn off the engine and wait a few minutes for the oil to settle.
- Check the oil level again using the dipstick. The oil level should still be between the “min” and “max” marks.
- Reset the maintenance minder. To do this, turn the ignition key to the “on” position without starting the engine. Then, press and hold the “select/reset” button on the instrument panel. After a few seconds, the maintenance minder will reset.
People Also Ask About How To Reset Dash After Oil Change 2006 Honda CR-V
What is the maintenance minder?
The maintenance minder is a system that tracks the vehicle’s maintenance needs. It uses a series of sensors to monitor the vehicle’s fluids, filters, and other components. When a maintenance item is due, the maintenance minder will display a message on the instrument panel.
How often does the maintenance minder need to be reset?
The maintenance minder should be reset every time the vehicle’s oil is changed.
Can I reset the maintenance minder myself?
Yes, you can reset the maintenance minder yourself by following the instructions in the owner’s manual.
