Is your LG dryer acting up? Experiencing unusual noises, inadequate drying performance, or unresponsive controls? Before you call for professional assistance or replace the entire machine, consider trying a simple yet effective solution: resetting your LG dryer. Resetting can often resolve minor software glitches and restore your dryer to optimal functionality.
To begin the reset process, locate the power cord at the back of the dryer. Unplug it from the electrical outlet and wait for at least 60 seconds. This time delay allows any remaining electrical charge to dissipate, ensuring a complete reset. After the waiting period, plug the dryer back into the outlet and turn it on. Observe if the problem persists. If not, your reset has successfully resolved the issue.
Should the problem remain after the reset, there may be an underlying hardware issue that requires professional attention. Contact an LG-authorized technician or repair service for further diagnosis and repair. In most cases, a simple reset can address many common dryer problems, saving you time, money, and the hassle of replacing the entire appliance.
Unplug the dryer
First, unplug the dryer from the power outlet. This will cut off the power to the dryer and allow you to safely reset it.
Locate the reset button
Once the dryer is unplugged, locate the reset button. The reset button is typically located on the back of the dryer, near the power cord. It is a small, round button that is usually red or black.
Press and hold the reset button
Once you have located the reset button, press and hold it for 5 seconds. This will reset the dryer and clear any error codes that may be stored in the dryer’s memory.
Plug the dryer back in
Once you have pressed and held the reset button for 5 seconds, plug the dryer back into the power outlet. The dryer will now be reset and ready to use.
Run a test cycle
To make sure that the dryer has been reset properly, run a test cycle. To do this, place a few wet clothes in the dryer and set the dryer to a normal cycle. The dryer should now run normally and dry the clothes without any problems.
Identifying the Problem
Is your LG dryer not performing as expected? Here are some common issues that may require a reset:
- Not starting or stopping unexpectedly
- Failing to heat or dry clothes effectively
- Making unusual noises or vibrations
- Displaying error codes or blinking lights
Troubleshooting
Before resetting your dryer, try the following troubleshooting tips:
- Check the power source: Ensure that the dryer is properly plugged into a working outlet and that the circuit breaker or fuse hasn’t tripped.
- Clean the lint filter: A clogged lint filter can restrict airflow, causing drying issues. Clean the filter after each load.
- Inspect the exhaust hose: A blocked or kinked exhaust hose can prevent proper venting and lead to poor drying performance. Check the hose for obstructions and ensure it’s securely connected to both the dryer and the outside vent.
- Empty the water reservoir (condenser models): Some LG dryers have a water reservoir that collects moisture. Empty the reservoir regularly to prevent overflow and drying issues.
Resetting Your LG Dryer
If troubleshooting doesn’t resolve the issue, you can reset your LG dryer to its factory settings. Here are three methods to do so:
| Method | Instructions |
|---|---|
| Control Panel Reset: 1. Press the Power button to turn on the dryer. 2. Simultaneously hold down the Wrinkle Care and Signal buttons for 5 seconds. 3. Release the buttons when the display shows "_ _". 4. Press the Start/Pause button to confirm the reset. |
|
| Dial Reset (for models with dials): 1. Turn the Mode and Cycle dials to the "Off" position. 2. Turn the Mode dial to any setting and back to "Off" three times. 3. Turn the Cycle dial to any setting and back to "Off" three times. 4. Turn the Mode and Cycle dials back to the "Off" position. |
|
| Breaker/Fuse Reset: 1. Turn off the circuit breaker or remove the fuse that powers the dryer. 2. Wait for a few minutes and then turn the power back on. 3. Press the Power button to restart the dryer. |
Power Cycle the Dryer
Unplug the dryer from the power outlet and wait about 5 minutes to allow the power to discharge from the dryer. This will reset the dryer’s control panel and clear any error codes that may be causing the dryer to malfunction. After 5 minutes, plug the dryer back into the power outlet and restart the dryer.
1. Locate the Power Cord
The power cord is typically located at the back of the dryer. It may be necessary to move the dryer away from the wall to access the power cord.
2. Unplug the Power Cord
Grasp the power cord firmly and pull it straight out of the power outlet. Do not yank on the cord, as this could damage the cord or the outlet.
3. Wait 5 Minutes
It is important to wait at least 5 minutes before plugging the dryer back in. This will allow the power to discharge from the dryer and the control panel to reset.
4. Plug the Power Cord Back In
After 5 minutes, plug the power cord back into the power outlet. Make sure that the cord is securely plugged in.
5. Restart the Dryer
Press the power button to restart the dryer. The dryer should now start operating normally.
If the dryer does not start operating normally after following these steps, it may be necessary to call a qualified appliance repair technician for assistance.
Resetting the Control Panel
Here’s how to reset the control panel of your LG dryer:
1. Unplug the Dryer
Locate the power cord and unplug the dryer from the electrical outlet.
2. Wait 5 Minutes
Allow the dryer to sit for at least 5 minutes to discharge any residual electricity.
3. Plug the Dryer Back In
After 5 minutes, replug the dryer into the electrical outlet.
4. Reset the Control Settings
Depending on your LG dryer model, you can reset the control settings in one of two ways:
Method 1: Manual Input
- Press and hold the “Temp” and “Signal” buttons simultaneously for 3 seconds.
- All the LED lights on the control panel should blink.
- Release the buttons once the lights stop blinking.
Method 2: Dial Control
- Ensure the dryer is turned off.
- Turn the cycle selector knob to the “Off” position.
- Press and hold the “Temp” and “Signal” buttons while turning the cycle selector knob clockwise to the “Normal” cycle.
- Release the buttons once the dial reaches the “Normal” cycle.
| Option | Value |
|---|---|
| Voltage | 110-120V 60Hz |
| Power Consumption | 1,650W |
| Capacity | 7.3 cubic feet |
| Dimensions | 29 x 29 x 39 inches |
| Weight | 132 pounds |
Unplugging and Replugging the Dryer
This simple step can often resolve minor glitches by resetting the dryer’s electrical components. Follow these instructions:
- Unplug the dryer from the electrical outlet.
- Wait for 30 seconds to allow the dryer to completely discharge.
- Recheck the electrical outlet to ensure it is providing power.
- Plug the dryer back into the outlet.
- Turn the power switch on and select a new cycle to see if the issue has been resolved.
Additional Tips for Unplugging and Replugging the Dryer
- Ensure the electrical outlet is in good working order by plugging in another appliance.
- If the dryer is not responding to power, check the circuit breaker or fuse box to make sure it hasn’t tripped.
- If the dryer only works on certain cycles, it may indicate a more complex issue that requires professional repair.
| Problem | Possible Cause |
|---|---|
| Dryer does not power on | Faulty electrical outlet, tripped circuit breaker, or blown fuse |
| Dryer does not heat | Malfunctioning heating element, temperature sensor, or control board |
| Dryer does not tumble | Broken belt, malfunctioning motor, or control board |
Resetting the Thermal Fuse
What is a thermal fuse?
A thermal fuse is a safety device that trips when the dryer overheats. This can happen if the lint trap is clogged, if the dryer vent is blocked, or if the dryer is overloaded.
How to reset a thermal fuse?
To reset a thermal fuse, you will need to:
- Unplug the dryer from the power outlet.
- Locate the thermal fuse. It is usually located on the back of the dryer, near the heating element.
- Use a multimeter to test the thermal fuse. If the fuse is blown, it will read “open” or “OL”.
- If the thermal fuse is blown, you will need to replace it. Thermal fuses are available at most hardware stores.
- Once you have replaced the thermal fuse, plug the dryer back into the power outlet and turn it on.
- If the dryer starts working again, the thermal fuse has been successfully reset.
Here is a table summarizing the steps on how to reset a thermal fuse:
| Step | Description |
|---|---|
| 1 | Unplug the dryer from the power outlet. |
| 2 | Locate the thermal fuse. It is usually located on the back of the dryer, near the heating element. |
| 3 | Use a multimeter to test the thermal fuse. If the fuse is blown, it will read “open” or “OL”. |
| 4 | If the thermal fuse is blown, you will need to replace it. Thermal fuses are available at most hardware stores. |
| 5 | Once you have replaced the thermal fuse, plug the dryer back into the power outlet and turn it on. |
| 6 | If the dryer starts working again, the thermal fuse has been successfully reset. |
Replacing the Door Switch
The door switch is a safety feature that prevents the dryer from operating when the door is open. If the door switch fails, the dryer will not start or stop when the door is opened.
To replace the door switch, you will need a Phillips head screwdriver.
1. Unplug the dryer from the power outlet.
2. Open the dryer door.
3. Locate the door switch. It is usually located near the top of the door opening.
4. Remove the two screws that hold the door switch in place.
5. Pull the door switch out of the dryer.
6. Disconnect the electrical connector from the door switch.
7. Connect the electrical connector to the new door switch.
Insert the new door switch into the dryer.
8. Secure the door switch in place with the two screws.
9. Close the dryer door.
10. Plug the dryer into the power outlet.
11. Test the door switch by opening and closing the dryer door.
The dryer should start or stop when the door is opened.
If the dryer does not start or stop, the door switch may be defective.
Here are some additional tips for replacing the door switch:
- If you are not comfortable replacing the door switch yourself, call a qualified appliance repair technician.
- Be sure to unplug the dryer from the power outlet before you start working on it.
- Do not touch the electrical connectors with your bare hands.
- If you have any questions, please consult your dryer’s owner’s manual.
Calling LG Customer Support
If you’ve tried all the troubleshooting steps above and your LG dryer is still not working, it’s time to call LG customer support. Here’s how to do it:
Contact Information
| Phone Number: | 1-800-243-0000 |
|---|---|
| Hours of Operation: | Monday-Friday: 8am – 8pm EST |
| Saturday: 9am – 6pm EST | |
| Sunday: Closed |
Tips for Calling Customer Support
- Have your dryer’s model and serial number ready.
- Describe the problem you’re experiencing in detail.
- Be prepared to answer questions about your dryer’s usage and maintenance.
- Be patient and polite. The customer support representative is there to help you.
Common Resetting Tips
1. Unplug the Dryer
Disconnect the dryer from the power supply for 1-2 minutes. This simple step can often resolve minor glitches and reset the dryer’s electronic components.
2. Check for Tripped Circuit Breakers
If your dryer is not responding, inspect your home’s circuit breaker panel or fuse box. Tripped breakers or blown fuses can cause power outages, including to appliances like dryers.
3. Inspect the Door Switch
A faulty door switch can prevent the dryer from starting. Make sure the door is securely closed and that the door switch is not damaged or misaligned.
4. Clean the Lint Filter
A clogged lint filter can restrict airflow and cause overheating, triggering automatic shutdown or error codes. Clean the filter after every cycle to ensure optimal performance.
5. Inspect the Exhaust Vent
Blocked exhaust vents can also cause overheating. Check the vent hose and outside exhaust hood for obstructions or blockages that may need to be cleared.
6. Reset the Thermal Fuse
Thermal fuses are safety devices that trip when the dryer overheats. Locate the thermal fuse on the back or bottom of the dryer and reset it by pressing the small red button.
7. Check the Heating Element
A malfunctioning heating element can cause the dryer to not heat up. Test the element with a multimeter to determine if it needs to be replaced.
8. Calibrate the Moisture Sensor
Some LG dryers feature moisture sensors that detect the dampness of clothes. Calibrate the sensor to ensure accurate drying performance.
9. Perform a Factory Reset
9.1 Press the “Start/Pause” and “Low Heat” Buttons Simultaneously
Hold both buttons for 5-10 seconds until the dryer beeps.
9.2 Turn the Dryer Off
Press the “Power” button to turn off the dryer.
9.3 Turn the Dryer Back On
Press the “Power” button again to turn the dryer back on. The factory reset will be completed.
9.4 Check the “FF” Code
After the reset, the display may show an “FF” code, indicating that the dryer has been successfully reset. If the code does not appear, repeat the steps.
Resetting Your LG Dryer
If your LG dryer is not functioning correctly, resetting it may resolve the issue. Here are the steps involved:
- Unplug the dryer from the power outlet.
- Wait at least 10 seconds.
- Plug the dryer back into the power outlet.
- Press and hold the “Start” button for 5 seconds.
- The dryer will beep and the display will show “88.”
- Press the “Options” button to select “00.”
- Press the “Start” button to confirm your selection.
- The dryer will beep again and the display will show “00.”
- Your dryer has now been reset.
- Unplug the dryer again and wait 10 seconds before plugging it back in to complete the reset.
Maintaining Your LG Dryer for Optimal Performance
Routine Maintenance
Regularly clean the lint filter before each load. Clean the exterior of the dryer with a damp cloth to remove any dust or debris.
Cleaning the Lint Filter
The lint filter is located on the top of the dryer door. It should be cleaned before each cycle to prevent lint buildup, which can cause reduced drying performance and potential fire hazards.
Cleaning the Condenser
The condenser is located at the bottom of the dryer and helps to remove moisture from the clothes. It should be cleaned every six months, or more frequently if you notice a decrease in drying performance.
Checking the Exhaust Vent
The exhaust vent should be checked every year to ensure it is clear of blockages, such as lint or debris. A clogged exhaust vent can cause poor drying performance and increased energy consumption.
Troubleshooting Common Issues
If you encounter any issues with your LG dryer, consult the user manual for troubleshooting tips. Common issues include:
| Symptoms | Possible Causes |
|---|---|
| Dryer is not starting | Unplugged power cord, faulty power outlet, blown fuse, or tripped circuit breaker. |
| Clothes are not drying properly | Clogged lint filter, clogged condenser, or blocked exhaust vent. |
| Dryer is overheating | Blocked exhaust vent, faulty heating element, or damaged thermostat. |
How to Reset an LG Dryer
Resetting your LG dryer can help resolve common issues and restore its optimal performance. Here are the steps to safely reset your dryer:
- Unplug the dryer: Disconnect the dryer from the electrical outlet to prevent any electrical accidents.
- Wait 1-2 minutes: Allow the dryer to cool down and discharge any residual power.
- Clean the lint filter: Remove the lint filter and clean it thoroughly to ensure proper airflow.
- Check the vent: Inspect the vent pipe for any blockages or restrictions that may hinder airflow.
- Reinstall the filter: Insert the clean lint filter back into the dryer.
- Plug in the dryer: Reconnect the dryer to the electrical outlet.
- Start the dryer: Press the power button to start the cycle.
People Also Ask About How to Reset LG Dryer
How often should I reset my LG dryer?
Regularly resetting your LG dryer is not necessary unless you encounter specific issues or performance problems.
What are some signs that my LG dryer needs to be reset?
If you notice decreased drying efficiency, excessive noise during operation, or error codes displayed on the control panel, resetting the dryer may help resolve these issues.
Can I reset my LG dryer using the control panel?
Method 1
Press and hold both the “Wrinkle Care” and “Sanitary” buttons simultaneously for 3-5 seconds until you hear a chime.
Method 2
- Turn the dryer off.
- Press and hold the “Power” button.
- While holding the “Power” button, press and release the “Start/Pause” button 3 times.
- Release the “Power” button.
